casappa齒輪泵PLP30系列
casappa齒輪泵PLP30.51D0-83E3-LED/EB-N-FS
CASAPPA提供:
Fixed and variable displacement hydraulic pumps and motors
齒輪泵、定量、變量液壓泵及液壓馬達
Hydraulic valves to control pressure and flow rate
壓力和流量控制器
Hydraulic filters
液壓濾清器
齒輪泵：
PLM系列：
PLM系列：
PHP系列：
KP系列：
PLP系列：
齒輪泵和電機內置三件鑄鐵閥體。
新的齒輪泵和電機“PH”系列是“POLARIS”系列的演變。
“POLARIS PH”具有由鑄鐵制成的新主體，具有更高的運行參數，并保持了對軸，法蘭，端口和內置閥門的全面POLARIS通用性。
該項目的目標是鏟車，滑移裝載機以及傳統鋁泵被迫接近極限的所有應用。除了增加強度之外，與鑄鐵蓋配合身體的可能性進一步降低了噪音水平。
從0.50in / rev（8,26cm / rev）到2.01in / rev（33,03cm / rev）的位移。
大。峰值壓力高達4350 psi（300 bar）。
大。速度可達3500分鐘
高工作壓力也適用于高位移
使用壽命長
低噪音水平
在高溫下也具有高體積效率
進出口優化 - 高速
組合在多個泵
內置閥門簡化了電路設計
內置閥門
防氣蝕閥
大減壓閥
優先閥
“負載感應”優先閥
旁通電動閥
比例安全閥
反向閥
Casappa柱塞泵LVP系列
特征
可變排量軸向柱塞泵斜盤設計。
PLATA泵非常適用于中高壓開路應用。
從1.75in / rev(28,7cm / rev)到5.36in / rev(87,9cm / rev)大。峰值壓力高達5075 psi(350 bar)
大 速度可達3000分鐘-1
節能
低噪音發射
響應時間短
驅動軸軸承適用于徑向和軸向負載
多重組合
控制
壓力補償器
流量和壓力補償器(負載感應)
扭矩限制器
電液伺服控制
選型資料如下：
POLARIS 10 gear pumps and motors meet a wide range of and industrial applications. SAE and EUROPEAN mounting flanges and rear covers are available in both cast iron and aluminum for reduced weight. The extruded aluminum body houses single piece gear, journal, shaft assemblies with a pressure balancing system that provides the highest volumetric and overall efficiencies available. Exceptionally large bearings make possible longer life at high pressure. A complete range of drive shafts in spline, parallel keyed, and tapered versions to meet all SAE, and EUROPEAN standards.
|
|
|
|
|
|
| Max. | Max. (2) | Pump | Motor |
|
|
| |
|
| POLARIS | POLARIS | Theoretical | Min. (1) | flow (3) | Approx. (5) |
| ||||||
|
| (1) | continuous | torque (4) |
| |||||||||
|
| displacement | speed | @ 1800 rpm | weight |
| ||||||||
|
| pump | motor | speed | pressure p1 | @ 100 psi |
| |||||||
|
|
|
|
| @ p1 |
|
|
| ||||||
|
| size | size |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
| in3 /rev | cm3 /rev | rpm | rpm | psi | bar | US gpm | lbf in | kg | lb |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| PLP 10-1 | PLM 10-1 | 0.06 | 1 | 650 | 4000 | 3770 | 260 | 0.46 | 0.84 | 1.40 | 3.09 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| PLP 10-1,5 (6) | PLM 10-1,5 (6) | 0.09 | 1.5 | 650 | 4000 | 3770 | 260 | 0.69 | 1.26 | 1.45 | 3.20 |
|
| 10 | PLP 10-2 | PLM 10-2 | 0.12 | 2 | 650 | 4000 | 3770 | 260 | 0.92 | 1.68 | 1.50 | 3.31 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| PLP 10-2,5 (6) | PLM 10-2,5 (6) | 0.15 | 2.5 | 650 | 4000 | 3770 | 260 | 1.15 | 2.10 | 1.52 | 3.35 |
| |
| POLARIS |
| ||||||||||||
01.1998 | PLP 10-3,15 | PLM 10-3,15 | 0.19 | 3.1 | 650 | 4000 | 3770 | 260 | 1.42 | 2.60 | 1.54 | 3.40 |
| |
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| PLP 10-4 | PLM 10-4 | 0.24 | 4 | 650 | 4000 | 3625 | 250 | 1.84 | 3.35 | 1.58 | 3.48 |
|
|
| PLP 10-5 | PLM 10-5 | 0.30 | 4.9 | 650 | 4000 | 3625 | 250 | 2.25 | 4.10 | 1.65 | 3.64 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| PLP 10-5,8 (7) | PLM 10-5,8 (7) | 0.35 | 5.8 | 650 | 3500 | 3300 | 230 | 2.67 | 4.86 | 1.70 | 3.75 |
|
Edition: |
| PLP 10-6,3 | PLM 10-6,3 | 0.38 | 6.2 | 650 | 3500 | 3300 | 230 | 2.85 | 5.20 | 1.73 | 3.81 |
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| PLP 10-8 | PLM 10-8 | 0.48 | 7.9 | 650 | 3500 | 2610 | 180 | 3.69 | 6.62 | 1.80 | 3.97 |
|
|
| PLP 10-10 | PLM 10-10 | 0.60 | 9.9 | 650 | 3500 | 2030 | 140 | 4.64 | 8.30 | 1.90 | 4.19 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
- Minimum speeds can be reduced, maximum speeds can be increased. For specific operating conditions consult tech-nical dept. for recommendations and approval.
- Significantly higher intermittent pressures are allowed. Consult catalog or contact technical dept.
- Flow shown is minimum allowed for production pump at rated pressure with 10 wt oil at 110° Fahrenheit and can be used to cal-culate minimum volumetric efficiency under these conditions.
- Indicated torque is obtained by considering the average mechanical efficiency.
- Weight shown is for pump and motor with cast iron end-covers. There is a weight reduction for aluminum covers.
- Available only for single units with shaft code 81.
- Available only for single units with shafts code 81 and 86.
casappa齒輪泵PLP30.51D0-83E3-LED/EB-N-FS
